12.5 C
New York
Wednesday, December 23, 2020
Home How to How to Use and Troubleshoot Blood Oxygen Monitoring on Apple Watch Series...

How to Use and Troubleshoot Blood Oxygen Monitoring on Apple Watch Series 6

Apple with the Apple Watch Series 6 introduced a new feature for monitoring blood oxygen level, using the LEDs at the back of the Apple Watch to determine the amount of oxygen in the blood. A low blood oxygen level can be indicative of a serious health issue that needs immediate attention.

Taking a blood oxygen reading is rather straightforward, but there are automatic measurement settings to be aware of as well as necessary tips for getting an accurate measurement, all of which can be found in the guide below.

How Blood Oxygen Readings on Apple Watch Work

The ‌Apple Watch Series 6‌ is equipped with green, red, and infrared LEDs that shine light onto the blood vessels in the wrist, with photodiodes measuring the amount of light reflected back.

Apple’s algorithms use this information to calculate the color of the blood, which is an indication of how much oxygen is in the blood. Bright red blood is well oxygenated, while darker blood has less oxygen.

The ‌Apple Watch Series 6‌ can measure blood oxygen levels between 70 and 100 percent. Most healthy people have blood oxygen levels that range from 95 to 100 percent, though those with COPD and other lung diseases may have a lower average percentage.

Apple does not expect the Blood Oxygen function in the Series 6 to be intended for medical use, and so the Apple Watch will not send a notification if a lower than normal blood oxygen level is detected.

Hardware Requirements

Using the Blood Oxygen monitoring feature requires an ‌Apple Watch Series 6‌ running the latest version of watchOS along with an iPhone 6s or later with the latest version of iOS.

The Blood Oxygen app is available in almost all countries around the world, but if you’re not seeing it, it might not be in your country. Apple has a list here.

Note that the Blood Oxygen app is not available to users under 18 and it is not enabled when an Apple Watch has been paired to an ‌iPhone‌ using Family Setup.

Enabling Blood Oxygen Measurements

When you set up a Series 6 Apple Watch, you’ll be asked during the setup process if you want to enable Blood Oxygen measurements. If you tap “enable” when asked, the feature will be turned on automatically and will be usable through the Blood Oxygen app.

How to Take a Blood Oxygen Measurement on Apple Watch

Make sure your ‌Apple Watch Series 6‌ is snug but comfortable on your wrist.

Open the Blood Oxygen app on your Apple Watch.

Keep still, and make sure your wrist is flat with the Apple Watch facing upwards.

Tap Start, then keep your arm steady for 15 seconds.

Wait for the measurement to be taken – you’ll see the result when it’s complete. Then tap Done.
You can view blood oxygen measurements taken over days, weeks, months, and years in the Health app on your ‌iPhone‌. Simply search for “Blood Oxygen.”

Automatic Blood Oxygen Readings

In addition to on-demand readings, the ‌Apple Watch Series 6‌ takes automatic blood oxygen readings throughout the day. Automatic blood oxygen measurements are enabled as long as Blood Oxygen Measurements are turned on and enabled, which is the default setting on the new Apple Watch.

Automatic blood oxygen readings are taken infrequently during the day, so you may only see these measurements a few times throughout your day, a departure from the frequency of heart rate measurements. Blood oxygen readings aren’t taken as often simply because the wrist needs to be held still and in a specific orientation for a measurement.

Enabling Automatic Blood Oxygen Readings in Theater Mode

The Apple Watch has a Theater Mode that keeps the display of the Apple Watch dim to prevent it from being a nuisance in dark places like movie theaters, and there’s a blood oxygen setting that can enable or disable readings during Theater Mode.

Apple says that blood oxygen readings require the use of a bright red light, which has the potential to be distracting in a dark room. Here’s how to enable or disable readings in Theater Mode.

Open up the Settings app on the Apple Watch.
Scroll down and tap on the Blood Oxygen app.
Scroll down and tap the toggle next to “In Theater Mode” to turn the feature on or off.

Enabling Automatic Blood Oxygen Readings During Sleep

As with Theater Mode, Apple has an option to disable blood oxygen readings when the Apple Watch is in Sleep Mode because the bright light might be distracting in the dark. Here’s how to enable or disable readings for Sleep Mode.

Open up the Settings app on the Apple Watch.
Scroll down and tap on the Blood Oxygen app.
Scroll down and tap the toggle next to “In Sleep Mode” to turn the feature on or off.

Viewing Blood Oxygen Data

No blood oxygen data can be viewed on the Apple Watch outside of the reading that you just took if you have the app open. Historical data needs to be viewed on the ‌iPhone‌, and it can be a little bit hard to find.

Here’s the easiest way to get to your data.

Open up the Health app on the ‌iPhone‌.
Tap on Browse at the bottom of the app.
Tap on Vitals or at the top of the app, search for Blood Oxygen.
Tap on the reading that comes up.

From here, you can see your average Blood Oxygen measurements by day, week, month or year, tapping on the chart to see specific information about each reading in day view or ranges for the other view options.

Tapping on “Show More Blood Oxygen Data” provides the latest reading, range over time, daily average, and readings in a High Elevation Environment or during sleep if those apply.

If you scroll all the way to the bottom of the app, there’s a “Show All Data” option that you can tap to see all of the blood oxygen measurements that have been taken with specific information on date, barometric pressure, and more.

Turn Off Blood Oxygen Monitoring

Don’t want to use blood oxygen monitoring at all? It can be disabled in the Settings app.

Open up the Settings app on the Apple Watch.
Scroll down and tap on the Blood Oxygen app.
Tap on the toggle next to “Blood Oxygen Measurements” to turn the feature off.

If you want to reenable blood oxygen readings at a later date, just turn the toggle back on. It’s enabled by default when you set up the Apple Watch, so the only reason you might need to enable it is if you’ve previously disabled it.

Blood Oxygen Troubleshooting

The sensors that measure oxygen level in the blood on the Apple Watch are highly sensitive and the reading will fail even if there’s minor movement. If you’re frequently getting an “Unsuccessful Measurement” warning, make sure to follow these steps.

Hold your wrist flat and face up, with your fingers also resting open. Blood oxygen measurements will not work if the arm is hanging down or if your fingers are in a fist.
Make sure the Apple Watch is snug against the wrist with a band that fits well and is not too loose or too tight.
Make sure the Apple Watch is flat against the wrist and not impeded by the wrist bone. If it is over the wrist bone, adjust the positioning of the watch.
For more stability, put your wrist on a table or flat surface such as your lap.
Minimize all movement for 15 seconds. The stiller you are, the better.
Don’t tap or otherwise engage with the Apple Watch. A tap on the screen or touching the Digital Crown can cause minute movement that disrupts the reading.

If you’re following all of the above steps and are still having trouble, Apple warns that there are a few scenarios that can cause poor readings.

  • Tattoos – Dark tattoos in the area where the sensors are located can cause the light that shines through the skin to measure oxygen level to fail to work properly. There’s no fix for this, unless there’s a non-tattooed wrist area available. Note that lighter tattoos may not interfere with the sensor, and it may also work with those that leave a good amount of skin visible.
  • Cold weather – If it’s cold outside, it can affect how much blood flows through your arm at any given time, which in turn can cause blood oxygen measurements to fail.
  • Skin perfusion – Regardless of weather, sometimes the blood flowing through the skin is slower, and this can vary significantly from person to person. Skin perfusion is a factor in how well the blood oxygen measurements work.
  • High heart rate – If your heart rate is above 150 beats per minute at rest, the blood oxygen measurement feature will not work.
  • Motion – As mentioned above, blood oxygen measurements tolerate little to no motion at all, and arm position is a factor. Hold the arm straight with your fingers out and try not to move if you’re having issues.

Guide Feedback

Have questions about blood oxygen monitoring on ‌Apple Watch Series 6‌ or want to offer feedback on this guide? Send us an email here.Related Roundup: Apple Watch Series 6Buyer’s Guide: Apple Watch (Buy Now)
This article, “How to Use and Troubleshoot Blood Oxygen Monitoring on Apple Watch Series 6” first appeared on MacRumors.com

Discuss this article in our forums

MacRumors-All?d=6W8y8wAjSf4 MacRumors-All?d=qj6IDK7rITs


8 Most Recommended Online SAT Prep Resources

It is no secret that your scores from the standardized college admissions test such as the ACT and SAT can dramatically influence...

Australian regulator threatens to block Google’s Fitbit takeover

Google says it will continue to engage with the regulator to answer their questions.What you need to knowThe Australian Competition

Score 400 lessons on web development and design for just $35 right now

It has never been easier to teach yourself something new or to pick up a side hustle. Whether it’s mobile apps, something for the cloud, web development, or something else, we’re in an age where having access to tools and teaching is only a mouse-click away.We’ve got a collection of training designed specifically with the would-be web developer in mind. Called the Ultimate 2021 Web Developer & Designer Super Bundle, it gives you all of the resources and education you need to gain an advantage in an increasingly competitive market. We’re talking nearly 40 hours of instruction spanning some 430+ lessons.Get started on a new career or take your current one to another level with the 14-course bundle from AndroidGuys Deals!What makes web developers so sought after? For starters, they can personally take ownership of every aspect of an app or site, understanding things anywhere in the development process. Moreover, they’ll understand languages that many other people do not and can debug, clean up code, or enhance an existing framework with new capabilities.Are you familiar with CSS, HTML, JavaScript, or other web development fundamentals? Why not resolve to make 2021 the year you change career paths or at least scratch that creative itch?FeaturesWeb Design JavaScript Frontend Code CourseWebsite QA for Web DesignersHTML 101: A Beginner’s Guide to CodingHTML 201: Intermediate level HTMLCSS 101: A Beginner’s Guide to Beautiful WebsitesCSS 201: Intermediate level CSSCSS 301: Responsive Web DesignUnderstanding How Websites WorkWeb Development FundamentalsHTML5 Canvas Element: Quick Introduction to Canvas HTML5HTML5 Canvas: Create 5 Games & 5 ProjectsJavaScript: Create 5 Fun Word GamesJavaScript Math Games: Project for Learning Code from ScratchHow to Get a Job as a Web DeveloperWhere to BuyThe Ultimate 2021 Web Developer & Designer Super Bundle can be yours for pennies on the dollar. Worth close to $2,000 if you were to go out on your own to get this education, you can purchase it for only $35. Hurry, this won’t last forever!Best SellersEarn Credits!For every $25 you spend in the AG Deals Store you get $1 credit added to your account. And, if you refer the deal via social media or an email that results in a purchase, you’ll earn $10 credit in your account.First Time Buying?If this is your first time buying, you are also eligible for 10% discount! Just be sure to subscribe for email updates.Free StuffNot looking to spend any money today? No worries. You can still visit the AndroidGuys section for freebies and pick something anyhow.

Xiaomi Mi 11 launch date announced, first phone with Snapdragon 888

Back a few weeks ago, when the Snapdragon 888 was announced, Qualcomm announced that one of their manufacturer partners was Xiaomi. Leaks came out suggesting that we could see a Xiaomi Mi 11 sporting the new chipset by the end of the year, with Xiaomi themselves saying that the Mi 11 would be one of the first devices to run on the Snapdragon 888, though no date came with that.Now, in a post on Weibo, a Chinese social media platform, co-founder Lei Jun has confirmed that we can expect the Xiaomi Mi 11 to come out on December 28th at 7:30PM.Leaks have been pretty far and few between, though information suggests the device will come in two variants, a standard and a pro, and both will support 55W fast wired charging. In addition to this, the Mi 11 might feature a 120Hz QHD+ display. However, we don’t have to wait long for any of these to be confirmed, with December 28th being less than a week away.